Fundamentals of Fluid Mechanics B Assignment 7 — Boundary Layer  
Instructions
Write your solutions in single column format, with one statement following another vertically. Write your solutions neatly so that they are easy to read and verify. Don't write one line with two equal signs. Highlight your answers using a box. Failure to do this will result in a lower score and fewer comments on my part.
04.18.20
Question #1
You perform an experiment in which liquid water at a temperature of 27$^\circ$C flows on a flat plate as follows:
figure5.png
The flat plate has a length $L$ of 2 meters, a height $H$ of 2 mm, and a depth $D$ of 1 meter. Knowing that the boundary layer thickness at the trailing edge of the plate is of $\delta=2.76$ cm, estimate as well as possible the total drag force on the plate caused by the flowing water. Please use the following data for liquid water: density $\rho=1000$ kg/m$^3$, viscosity $\mu=10^{-3}$ kg/ms, heat capacity $c=c_p=c_v=4200~$J/kgK, conductivity $k=0.6~$W/mK.
Question #2
(a)  The momentum thickness of the boundary layer corresponds to the height of the inflow that is responsible for the momentum within the boundary layer, as follows:
A8Q3.png  ./download/file.php?id=7772&sid=da4f00da1fd593b5837bc366b0b23461  ./download/file.php?id=7772&t=1&sid=da4f00da1fd593b5837bc366b0b23461
Find an expression for $\delta_m$ that is applicable to a constant pressure boundary layer over a flat plate in which the density is not constant but the viscosity is constant. Simplify the expression as much as possible.
(b)  For the case of a constant density and constant viscosity boundary layer, find an expression for $\delta_m/\delta$ and simplify as much as possible. Outline all assumptions.
04.15.21
Question #3
Consider a cone with its tip being sawed off. The tip radius is of $R_0$ and the radius of the cone corresponds to $as+R_0$ with $a$ a constant and $s$ a coordinate parallel to the cone surface. Starting from the Mangler's transform: $$ \hat{s}=\int_0^s \frac{R^2}{L^2} ds ~~~,~~~ \hat{n}=\frac{R}{L}n ~~~,~~~ \hat{v}_s = v_s ~~~,~~~ \hat{v}_n = \frac{L}{R} \left( v_n + \frac{n}{R} v_s \frac{dR}{ds}\right) $$ and the expressions previously derived for a planar boundary layer using a polynomial fit for the velocity: $$ \frac{\delta}{x} = 4.64 {\rm Re}^{-0.5}_x ~~,~~ \frac{u}{U_\infty}=\frac{3}{2}\frac{y}{\delta} - \frac{1}{2}\left( \frac{y}{\delta}\right)^3 $$ do the following:
(a)  Derive an expression for the characteristic length $L$ applicable to this problem.
(b)  Derive an expression for $v_s$ as a function of $n$ and $\delta$ through the axisymmetric boundary layer.
(c)  Derive an expression for the skin friction coefficient of the axisymmetric boundary layer.
(d)  Find an expression for the ratio between the axisymmetric $C_f$ and the planar $C_f$. Show that this ratio depends on only one non-dimensional parameter.
04.07.22
Answers
1.  0.0246 N.
Due on Wednesday April 20th by 16:00 in my office. Do all problems.
PDF 1✕1 2✕1 2✕2
$\pi$
cron